It is 6 a.m., the wind off Lake Erie is rattling the windows, and the radiators are stone cold. If your boiler is not working, you are not alone: older homes in Parkside, North Buffalo, South Buffalo and across the inner-ring suburbs lean heavily on hot-water and steam systems, and January is when they get tested hardest. This guide walks you through the checks that are safe for a homeowner, in the order that solves the most problems fastest, and tells you exactly when to stop and call someone.
Quick answer: When a boiler stops heating, check the basics first: thermostat settings and batteries, the boiler’s power switch and breaker, the gas supply, and the pressure gauge (hot-water boilers usually want roughly 12 to 15 psi when cold). Then look for a tripped pilot or ignition lockout, trapped air in radiators, and, on high-efficiency units, a frozen condensate line. If you smell gas, see water leaking, or a carbon monoxide alarm sounds, stop, leave the house and call for help right away.
Need a hand now? You can request boiler repair from a vetted local pro using the form on this page, and we will get you connected.
Safety first: when to stop and call a pro
Most boiler problems are minor, but a few are not. Before you touch anything, know the red lines.
- You smell gas (rotten eggs): do not flip switches or light anything. Get everyone out, then call National Fuel’s emergency line or 911 from outside.
- A carbon monoxide alarm is sounding: leave the house, call 911, and do not go back in until responders clear it.
- Water is leaking or pooling around the boiler, or the pressure relief valve is dripping steadily.
- Soot, scorch marks, or a yellow, lazy flame where you would expect a clean blue one.
- Banging, roaring or rumbling that is new and loud.
Everything else below is fair game for a careful homeowner. If a step makes you uneasy, that is a perfectly good reason to stop and call a licensed technician. For a deeper look at the CO side of things, our upcoming guide on carbon monoxide and furnace safety in Buffalo winters covers alarms and placement.
Gas smell, leak or CO alarm means leave first and troubleshoot never.
Step 1: Check the thermostat and power
It sounds too simple, but a surprising share of no-heat calls end here. Start at the thermostat.
- Set it to Heat and turn the target temperature at least 5 degrees above the room temperature.
- Replace the batteries if the display is blank or dim.
- Check that a programmable or smart thermostat has not switched to an away schedule or lost its Wi-Fi settings.
- At the boiler, confirm the power switch (often a red switch on a nearby wall or the basement stairs) is on.
- Check the breaker panel for a tripped breaker labeled boiler or furnace.
If the house lost power during a lake-effect storm, the boiler may need a manual restart once the lights come back. Our guide to Buffalo power outages and winter storm prep covers what to do when the grid goes down and what to check after it returns.
Step 2: Check boiler pressure
Hot-water boilers need the right amount of water in the system. Look for the round pressure gauge on the boiler. When the system is cold, most residential boilers sit around 12 to 15 psi, though your manual has the exact number for your unit.
If the needle is near zero, the boiler may have locked out on low pressure. Many boilers have a fill valve or a small lever on the water feed line; adding water slowly until the gauge reaches the normal range is a common homeowner step, but only if your manual says so. If pressure keeps dropping after you refill, you likely have a leak somewhere in the system, and that is a pro job. If the gauge reads very high (near 30 psi) or the relief valve is spitting, shut the boiler off and call for service.
Steam boilers work differently. They have a sight glass showing water level, and low water is a frequent cause of shutdown. Do not keep adding water to a hot steam boiler; let it cool and follow your manual or call a technician.
Step 3: Look at ignition, the pilot and error codes
Older boilers, which you will find in plenty of homes in the Elmwood Village, Allentown and the West Side, may have a standing pilot light. If it is out, relighting it with the manufacturer’s instructions is a normal homeowner task, as long as you do not smell gas. If it will not stay lit after one or two tries, stop; a failing thermocouple or gas valve needs a professional.
Newer boilers use electronic ignition and show fault codes on a small display. Write the code down and check the manual or the manufacturer’s website. Common culprits include a dirty flame sensor, a blocked vent, or a lockout. Many units let you press a reset button once. If it fires up and then locks out again, resetting repeatedly will not fix the underlying issue and can be unsafe.
One reset is a reasonable test; repeated resets just hide a problem that needs a technician.
Step 4: Cold radiators, trapped air and zone valves
If the boiler runs and the pipes are warm but some radiators stay cold, the usual suspect is trapped air. The top of the radiator will be cool while the bottom is warm, and you may hear gurgling. Bleeding the radiator with a key releases that air and lets hot water circulate again. We are putting together a step-by-step on how to bleed a radiator in Buffalo’s older homes, but the short version is: turn the boiler off, open the bleed valve slightly with a radiator key, close it when water starts to dribble, and recheck the system pressure afterward.
If an entire floor or zone is cold while others heat fine, you may have a stuck zone valve or a failed circulator pump. A pump that is silent, hot to the touch or noisy is not a DIY repair. Also check that radiator valves are fully open and that nothing, like furniture or heavy drapes, is blocking heat.
| Symptom | Likely cause | DIY or pro? |
|---|---|---|
| Blank thermostat | Dead batteries or no power | DIY |
| Pressure near zero | Low water or a leak | DIY refill once; pro if it repeats |
| Top of radiator cool, bottom warm | Trapped air | DIY bleed |
| One zone cold, others hot | Zone valve or circulator issue | Pro |
| Pilot will not stay lit | Thermocouple or gas valve | Pro |
| Water on the floor | Leak or failed component | Pro |
Step 5: Frozen condensate line on high-efficiency boilers
Modern condensing boilers are very efficient because they pull extra heat out of the exhaust, which creates acidic water that drains out through a small plastic condensate line. In a Buffalo cold snap, that line can freeze, especially if it runs through an unheated space or out an exterior wall. When it does, the boiler shuts down and often shows a condensate or blocked-drain fault.
You can try gently thawing the line with warm (not boiling) water or a hair dryer on low, then restart the boiler. Never use an open flame or a heat gun. If the line is inaccessible, repeatedly freezes, or the boiler still will not start, a pro can reroute or insulate it. Frozen pipes are a related risk in this weather, and our article on whether homeowners insurance covers burst or frozen pipes is worth a read before you need it.
Local tip: If your condensate line freezes every cold snap, ask a technician about insulating it, shortening its run, or adding heat tape rated for plastic drain lines. A cheap fix now beats a no-heat call at 2 a.m. during a January lake-effect band.
No hot water, or hot water but no heat?
If your boiler also feeds an indirect water heater or tankless coil, the same checks apply, but the symptoms can split. Hot water with no heat often points to a thermostat, zone valve or circulator issue. Heat with no hot water can mean a failed diverter, a tripped aquastat or a problem with the indirect tank. If your hot water comes from a separate tank, our upcoming guide on what to do when a water heater is not working in winter will help sort it out.
Meanwhile, if you are only getting cold air from vents rather than radiators, you probably have a forced-air system instead, and our furnace blowing cold air troubleshooting guide is the better fit.
When to call a pro (and what to expect)
If you have worked through the basics and the boiler is still down, it is time to bring in a licensed technician. Gas valves, heat exchangers, circulators, relief valves and combustion problems are not DIY territory. Ask whether the company is licensed and insured, whether they service your boiler type (steam, hot-water, condensing), and how they handle emergency visits. Prices vary widely, so get an estimate before work begins. For a fuller picture of the process, our emergency furnace repair guide covers what to do when heat dies in the middle of winter, and much of it applies to boilers too.
If your boiler is decades old, needs frequent repairs or is struggling to keep up, it may be cheaper long-term to replace it. Our guide to boiler replacement in older Buffalo homes explains your options for radiators, steam and hot water. If money is tight, see whether you qualify for help through HEAP in Erie County.
Ready to get it fixed? Request boiler repair from a vetted local pro using the form on this page, and someone will reach out.
How to keep it from happening again
Most no-heat emergencies trace back to skipped maintenance. A yearly tune-up lets a technician check pressure, test safety controls, clean the burner and spot worn parts before they fail. Our guide to boiler maintenance before and during winter lays out what to do and when. It also pays to bleed radiators each fall, keep the area around the boiler clear, and make sure carbon monoxide alarms have fresh batteries.
FAQ
Why is my boiler on but my radiators are cold?
The most common reasons are trapped air in the radiators, low system pressure, a failed circulator pump or a stuck zone valve. Bleed the radiators and check the pressure gauge first. If the pipes themselves are cold, call a pro.
What should my boiler pressure be?
Many residential hot-water boilers run around 12 to 15 psi when cold and a bit higher when hot, but your manual has the exact range. Near zero means low water or a leak; very high readings mean you should shut it off and call for service.
Can I reset my boiler myself?
Usually once, following the manufacturer’s instructions. If it locks out again, stop resetting and call a technician, because repeated lockouts point to a real fault.
Why does my boiler stop working in the coldest weather?
Extreme cold can freeze the condensate line on high-efficiency units, and it also stresses older components that are already worn. Regular maintenance and insulating exposed lines help a lot.
Is a boiler not heating an emergency?
In a Buffalo winter, a house with no heat can become unsafe quickly, especially with young children, older adults or pipes at risk of freezing. Any gas smell, leak or CO alarm is always an emergency.
Get boiler repair help from Buffalo pros
A vetted local pro will reach out with a free, no-obligation quote.
